Tunturi J7F User Manual download pdf (Page 9)

G B

O W N E R ' S M A N U A L • J 7 • J 7 F

If the belt is allowed run across to one side

for long periods of time the edges of the belt may

be damaged and the treadmill may not continue to

operate correctly. Any damage to the belt caused

by the lack of necessary adjustment will not be

covered by the warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on

the rollers. In normal use, however, keep the belt

as loose as possible! The belt tension is adjusted by

turning the same screws as used for aligning the

running belt. If turning the screws will not effect

the belt tension, please contact your Tunturi dealer.

1. Increase the treadmill’s speed to 5 km/h (3

mph).

2. Turn both adjustment screws an equal amount,

1/8 turn clockwise.

3. Try to slow the belt down by holding onto the

handrails and braking as you walk (as if you were

walking downhill). If the belt slips, turn another

1/8 turn and repeat the test. When braking heavily

the belt may slip.

MALFUNCTIONS

NOTE ! Despite continuous quality control, defects

and malfunctions caused by individual components

may occur in the equipment. In most cases it’s

unnecessary to take the whole device in for

repair, as it’s usually sufcient to replace the

defective part. If you require spare parts or the

equipment does not function properly during use,

contact your Tunturi dealer. Always give the model,

serial number of your equipment and in case

of malfunctions also conditions of use, nature of

malfunction and any error code. Use only spare

parts mentioned in the spare part list. If there is

a fault in the user interface display, unscrew the

10 locking screws. Detach the cable connector by

pressing the clip towards the cable and pulling it

off. Be careful not to drop the cable inside the tube.

Please contact your local Tunturi distributor

for further information on repairing or replacing

the meter. When reinstalling the user interface,

please tug lightly at the cable to make sure that it’s

properly locked.

NOTE ! The text “Self cal” on display indicates

automatic re-calibration of the lift motor.

M O V I N G A N D S T O R A G E

Before moving J7, be sure the power cord is

unplugged from the wall and the treadmill. Lift the

treadmill from the rear to an angle of about 30

degrees and push it on the front wheels. Lower the

treadmill carefully onto the oor.

You can lift up the running deck of J7F to a

space-saving storage position: Turn off the power

switch. Take hold of the frame tube underneath the

rear part of the running base and lift the running

base up.

CAUTION! The gas spring is designed to make

lifting the running base easier. Always remember

to ensure that the running base is locked in the

storage position!

Before moving J7F, be sure the power cord is

unplugged from the wall and the treadmill; lift up

the running base until it becomes locked. Stand

behind the treadmill and support it with your foot

on a transportation wheel, grip the hand rails and

tilt the treadmill towards yourself so that it rests

on the transportation wheels. Lower the treadmill

carefully onto the oor, again supporting it with

your foot.

NOTE ! Transport the treadmill with extreme

caution over uneven surfaces, for example over a

step. The treadmill should never be transported

upstairs using the wheels over the steps, instead it

must be carried.

NOTE ! The running belt needs to be realigned

and centered after moving.

To prevent malfunctioning of the treadmill,

store it in a dry place with as little temperature

variation as possible, protected against dust. Always

unplug the treadmill from the electrical outlet

when not in use.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 71 72

Comments to this Manuals

No comments

Tunturi J7F User Manual Page 9

Comments to this Manuals

Related products and manuals for Sports and recreation Tunturi J7F