Tunturi T80 User Manual download pdf (Page 13)

O W N E R ’ S M A N U A L

•

T 8 0 T 8 5

4. Spray the lubricant for 2-3 seconds.

5. Lower the running deck into its normal position.

Use treadmill for your training session. Or allow the

treadmill to run for at least 5 minutes.

NOTE! Lubricate your treadmill only with T-Lube

S silicon lubricant. Contact your local Tunturi

distributor for further supplies of T-Lube or further

information on lubrication and maintenance.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and make

adjustments as needed. The belt should run in the

center of the treadmill. Alignment is not usually

needed, provided

•

the treadmill is placed on an even, solid and

horizontal surface and the belt is correctly tensioned

•

the alignment of the belt is correct

It is, however, possible for the belt to be pushed to

one side due to the user’s running style (e.g. more

weight on one foot). The alignment of the belt is

adjusted by turning the two bolts at the back of the

treadmill.

ALIGN THE BELT ACCORDING TO THE FOLLOWING

INSTRUCTIONS:

1. Turn the power switch on and increase the

treadmill’s speed to 5 km/h (3 mph).

2. If the belt drifts to the left, turn the left adjustment

bolt ¼ turn clockwise and the right adjustment bolt

1/8 turn anti-clockwise. If the belt drifts to the right,

turn the right adjustment bolt ¼ turn clockwise and

the left adjustment bolt ¼ turn anti-clockwise.

3. If the belt remains centered the adjustment is

correct. If not, continue to make small adjustments

as above until the belt is correctly aligned. If the belt

is allowed run across to one side for long periods of

time the edges of the belt may be damaged and the

treadmill may not continue to operate correctly. Any

damage to the belt caused by the lack of necessary

adjustment will not be covered by the warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on

the rollers. In normal use, however, keep the belt

as loose as possible! The belt tension is adjusted by

turning the same screws as used for aligning the

running belt. If turning the screws will not effect the

belt tension, please contact your local Tunturi dealer.

1. Increase the treadmill’s speed to 5 km/h (3 mph).

2. Turn both adjustment screws an equal amount, ¼

turn clockwise.

3. Try to slow the belt down by holding onto the

handrails and braking as you walk (as if you were

walking downhill).

If the belt slips, turn another ¼ turn and repeat the

test. When braking heavily the belt may slip. If the

belt keeps slipping despite repeated adjustments,

please contact your local Tunturi dealer.

MALFUNCTIONS

NOTE! Despite continuous quality control, defects

and malfunctions caused by individual components

may occur in the equipment. In most cases it’s

unnecessary to take the whole device in for repair,

as it’s usually sufficient to replace the defective

part. Always give the model, serial number of

your equipment and in case of malfunctions also

conditions of use, nature of malfunction and any

error code.

When you encounter unusual behavior from the

treadmill, simply turn the power switch off, wait 1

minute and turn the power switch on to reset the

treadmill. This should clear incidental errors and

ready the treadmill for normal operation again. If

after you have reset the treadmill by turning the

power switch off and on again, and the treadmill

is still not operational, contact your local Tunturi

dealer for service.

If you require spare parts, always give the model,

serial number of your equipment and the spare part

number for the part you need. The spare part list

is at the back of this manual. Use only spare parts

mentioned in the spare part list.

ERROR CODES

The user interface will display information about

operational faults.

SYSTEM CHECK FAILED. Possible motor controller

fault. Turn the power switch off, wait 1 minute and

turn the power switch on again. If treadmill recovers

to normal operation, you may continue to use the

treadmill. Otherwise, call the dealer for service.

SPEED SENSOR ERROR. Call the dealer for service.

MOTOR SPEED ERROR. Ensure correct usage of

the treadmill. Do not push the belt with your feet.

Turn the power switch off, wait 1 minute and turn

the power switch on again. If treadmill recovers

to normal operation, you may continue to use the

treadmill. Otherwise, call the dealer for service.

MOTOR OVERLOAD. Ensure correct usage of the

treadmill. Do not brake the belt. Turn the power

switch off, wait 1 minute and turn the power switch

on again. If treadmill recovers to normal operation,

you may continue to use the treadmill. Ensure the

lubrication is sufficient, re-lubricate the running

deck if needed. Otherwise, call the dealer for service.

LIFT MOTOR ERROR. Call the dealer for service.

LIFT MOTOR OVERLOAD - Ensure correct usage

of the treadmill. Do not overload the lift motor

by continuously changing the elevation. Turn the

power switch off, wait 1 minute and turn the power

switch on again. The lift motor will be automatically

calibrated when the power switch is turned on. If

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 115 116

Comments to this Manuals

No comments

Tunturi T80 User Manual Page 13

Comments to this Manuals

Related products and manuals for Sports and recreation Tunturi T80